No heat? Same-day furnace repair across Douglas County · Call (720) 964-2178 Diagnostic $85, credited toward your repair · Free replacement estimates

Heating tips

Furnace Won't Ignite? What to Check Before You Call

The thermostat calls for heat and the furnace clicks or hums, but the burners never light — or they light for a few seconds and go out. Here's how a gas furnace starts, what you can safely check yourself, and when it's time to call a technician.

Smell gas? Don't try to start the furnace and don't flip any switches. Get everyone out of the house, then call 911 or Xcel Energy at 1-800-895-2999 from outside.

How a gas furnace lights

A modern gas furnace has no pilot flame burning all the time. Every time the thermostat calls for heat, the control board runs the same start-up sequence, and each step has to pass a safety check before the next one begins:

  1. The thermostat calls for heat.
  2. The inducer motor starts. It's a small fan that pushes exhaust out through the vent pipe — the hum you hear first.
  3. A pressure switch confirms the vent is clear.
  4. The igniter heats up and glows bright orange. Some furnaces use a spark instead.
  5. The gas valve opens and the burners light.
  6. The flame sensor confirms there's a flame. If it can't, the gas valve closes within seconds.
  7. The blower starts once the furnace has warmed up, and sends warm air through the house.

If any step fails, the furnace stops and tries again. After a few failed tries, most furnaces lock themselves out for a while and show an error code with a blinking light. That lockout is a safety feature: it also tells you, and the technician, where the sequence stopped.

Blue flames on every burner of a gas furnace
When ignition works, every burner lights within seconds with a steady blue flame.

7 checks you can do yourself

None of these need tools, and none of them involve opening the burner compartment.

  1. Thermostat

    It's set to Heat, the set temperature is a few degrees above the room, and the screen isn't blank — a blank screen usually means dead batteries. On a smart thermostat, make sure a schedule or an "away" mode isn't holding the temperature down.

  2. Furnace power switch and breaker

    On or near the furnace there's a switch that looks like a light switch, and it's easy to flip off by mistake. Make sure it's on, and that the furnace breaker in the electrical panel hasn't tripped.

  3. Door panel

    The front panel presses a safety switch. If the panel is loose or was put back crooked, the furnace won't start. Seat it firmly.

  4. Gas supply

    Do your other gas appliances work — the stove, the water heater? On the gas pipe going into the furnace there's a shut-off valve: its handle should point along the pipe. If it's turned across the pipe and you don't know why it was shut off, leave it and call us.

  5. Air filter

    A clogged filter makes the furnace overheat, so it lights and then shuts itself off. If you can't see light through the filter, replace it.

  6. Status light

    Most furnaces have a small light you can see through a window in the lower panel. Count the blinks and match them to the code chart on the inside of the furnace door. Take a photo of both — it helps when you call.

  7. One reset — only one

    Turn the furnace power switch off for 30 seconds, then back on, and watch: does the inducer hum? Does the igniter glow? Does a flame appear and then go out? If the furnace fails again, leave it off and call. Resetting it over and over won't fix the cause.

What the symptoms usually point to

Watch one start-up attempt and note where it stops. That's the most useful thing you can tell a technician.

What you see or hearWhere the start-up stops
Nothing at all: no hum, no click, no lightNo power or no call for heat: the thermostat, the power switch or breaker, the door switch, or a blown fuse on the control board
The inducer hums, but the igniter never glowsThe pressure switch can't confirm the vent: a blocked vent pipe or condensate drain, or a failing inducer motor or switch
The igniter glows, but nothing lightsNo gas reaching the burners, or a gas valve that doesn't open
A flame for a few seconds, then it goes outThe furnace can't confirm the flame: often the flame sensor, sometimes gas pressure or wiring
Runs for a few minutes, then shuts offOverheating: a clogged filter, closed or blocked vents, or a weak blower

These are the usual suspects, not a diagnosis. The same symptom can have more than one cause, which is why a technician tests each step before replacing any part.

When to stop and call

  • You smell gas. Leave the house first, then call 911 or Xcel Energy from outside.
  • A carbon monoxide alarm goes off. Here's what to do when a CO alarm sounds.
  • You hear a loud bang or "whoomp" when the burners light. Delayed ignition is a safety problem: turn the furnace off.
  • You see scorch marks or melted wires, or smell burning plastic.
  • There's water on the floor around the furnace.
  • The furnace fails again after one reset.

What happens when you call us

Call (720) 964-2178 or book online. No-heat calls get priority, and same-day or next-day visits are often available. The diagnostic visit is $85 and is credited toward your repair. The technician finds where the start-up fails and gives you the repair price before any work starts — and if the repair isn't done right, we come back and fix it at no charge.

Tell us what you saw during the reset and what the status light shows. It helps us narrow down the cause before we arrive.

How to keep it from happening again

Ignition parts wear out slowly, so a furnace that lit fine last winter can fail on the first cold night. A yearly furnace tune-up checks the burners and the ignition system before the season starts. Our Furnace Tune-Up & Safety Check is a flat $179, with no upsell and a written report with photos.

Between visits, check the air filter once a month during the heating season and replace it when it's dirty.

FAQ

Frequently asked questions

Why does my furnace click but not ignite?

The clicks are the control board and the igniter trying to start the furnace. If the burners never light, the start-up is stopping at a safety check or no gas is reaching the burners. Check the gas supply and the status light code, try one reset, and call if it still won't light.

Is it safe to keep resetting my furnace?

One reset is fine. If the furnace fails again, leave it off: resetting it over and over doesn't fix the cause, and a furnace that keeps locking out is protecting itself from an unsafe condition.

How much does it cost to fix a furnace that won't ignite?

It depends on what failed. Our diagnostic visit is $85 and is credited toward the repair, and you get the repair price before any work starts.

Can I light my furnace by hand?

Not a modern furnace: it lights itself with an electronic igniter and has no pilot to light. Only an older furnace with a standing pilot can be relit, by following the lighting instructions on its label. Never hold a flame to the burners.

Heat not working right?

Call us or book online. The $85 diagnostic visit is credited toward your repair, and you get the price before any work starts.